For modellers wanting to build up a 1/35 scale UH-60 and its variants, the various offerings from Kittyhawk are often the only game in town. Released just before 2020, KH’s family of UH-60 kits are often infamous for their fit issues while being somewhat expensive solely due to the fact that these are rare subjects, especially in 1/35th scale.
The Pavehawk: An Introduction
The HH-60G Pavehawk has long been an icon of the U.S Military, seeing service from 1982 to 2021. Primarily tasked with Air Force search and rescue operations as well as Pararescue medivac, Pavehawks have participated in wide ranging operations from the jungles of Panama to the mountains of Afghanistan.
The Kittyhawk offering
Kittyhawk kits have an unfortunate reputation among modellers due to several issues, ranging from general poor fit to fuselage warping. Despite these shortcomings, there really isn’t much selection for modelling large scale UH-60’s with older Academy and MRC moldings offering more basic variants of the Blackhawk. ICM has recently released their own 1/35 UH-60 however at the time of writing, there hasn’t been any further sub variants of this kit released yet.
My HH-60G build:
Construction starts with building up the cabin using the floor, ceiling, and side bulkhead parts. Right off the start I found the fit for these parts to be particularly tough and I had to spend some time sanding and slicing away material to ensure that these parts would join together smoothly. Getting good fit is important with the cabin parts because any conflict here will lead to further issues down the road. Next, I moved on to adding my own detail to areas that I found were lacking. From my reference photos I could see that there was some structural ribbing underneath the gunner windows that was not replicated by the kit. I decided to try my hand at recreating this detail and to do so I cut out some styrene sheets and added some decal rivets over top. This is a really small detail, but I’m glad I spent the hour or two recreating it.
I then moved on the overhead cockpit panel, taking a knife to the the molded on detail here. The kit has excellent molded detail, however I decided to go through the trouble with adding Anyz switches and dials so this existing detail would need to be removed. I then drilled out where the new switches would have to be with a 0.2mm drill bit.
After this initial scratch work was completed, I then moved on to paint. These parts were primed in my go-to primer, Mr. Finishing Surfacer 1500 Black before some SMS Lacquer U.S Medium Grey was sprayed over in a uniform coat. I masked off the sections of the cabin ceiling according to my references which nicely adds some visual interest. I then hit the overhead control panel with a subtle dark grey dry brushing to bring out some definition to this area.
I then got to work on the floor and sides of the cabin. The fuselage sides went together fairly straightforwardly, and were assembled out of a few pieces that must be aligned correctly with one another. I made the mistake of assembling this part before painting. Doing this necessitated some tricky masking between the green sections and the black cockpit parts. Nonetheless, I was able to complete the required painting and moved on to the cabin floor.
The cabin floor was definitely the most tedious part of this phase of the build, largely due to the fact that some excessive masking was needed to recreate the wear strips present on the floor of the cabin. These strips are always heavily worn in photos and I used the hairspray method to recreate this wear pattern. After this job was done, I sealed everything in a GX100 Gloss varnish in preparation of weathering.
With my previous work sealed under a varnish, I could then start the weathering process for the painted surfaces. I chose to keep things simple here and limited myself to a dark brown oil wash to highlight the surface detail yet not overwhelm it. After all, this is a modern aircraft and unlikely to get too dirty. I then sealed my work in a GX114 Matte clear coat.
After all my prior work had been sealed, I then got to work on the cockpit section. I had deliberately set this section aside, with the intention of painting and weathering it separately from the main cabin. References showed a fairly deep black as the cockpit colour, so I opted for Tamiya’s Flat Black instead of my standard NATO Black. I got started on the weathering right away and first applied some Vallejo Black Grey paint chips with a sponge. These are really subtle and only show up in the right light, however I fell that they accurately depict superficial scuffs that would be seen in this area. I then moved on to more substantial chips with Tamiya’s Zinc Chromate paint, followed by some silver. From my references I was able to see that many of the bolts and screw heads had had paint entirely worn off which I tried to recreate in my build. I then moved on to some more scratch work, adding detail underneath the seats. References again showed that this area was a maze of avionics and cables. I chose to recreate this mess with some styrene rectangles and lead wire.
With the cockpit floor completed, I was then able to move on to other various subcomponents, namely the instrument panels and seats. As with the overhead panel, I opted to use Anyz switches and dials to enhance the cockpit and give a more tactile feeling to this area. I started with the front panel, first painting it flat black before applying a grey drybrushing to highlight raised surfaces. I then added various instrument dial decals from a Jira-GIO decal sheet, which were then sealed over with some clear UV resin. I added some photography film to replicate the displays and declared this part complete. I didn’t want this part to appear too dirty so I kept the weathering very minimal.
I next moved on to the large centre instrument panel. This part is very much a focus point as it takes up a lot of space in the cockpit and is filled with many different switches and dials. I built up this part the same way I make many of my cockpits, I first scraped away the existing detail before drilling out where the new switches would be placed. The painting was done the same as the front panel, with flat black followed by a grey dry brushing prior to decal application. Minimal weathering was done on this part as well.
The seats were somewhat fiddly assemblies without great alignment. In reference photos I saw that these seats often had a fuzzy, soft material that I wanted to replicate. To do this, I added some Mr. Surfacer 500 paste which I stippled to create a rough surface on the seats. After a quick layer of black, I applied a light grey dry brushing to bring out the texture of the fabric. The cabin seats were also difficult to assemble with unclear angles for gluing. I used oils to depict a dirty, stained surface on these parts.
The next part of the cabin assembly that I moved onto was the internal fuel tank that many HH-60’s have fitted. This was a fairly easy part to build up, although I complicated it by swapping out the ratchet straps included int he kit with photo-etch ones from Czech manufacturer Miryoku. The specific aircraft I’m building, SN# 26206, was indicated as having a large American flag applied to this tank which I thought was particularly striking.
With the majority of the internal components completed, I could then start to think about starting to bring everything together. I did several test fits to ensure that the parts fit together well and that there wouldn’t be any conflicts when the cabin was sealed into the fuseluage.
Bringing everything together:
I first attached the middle and rear bulkheads to their respective spots on the floor and ceiling. Next, I then glued the fuel tank into place and attached the straps to their attachment points. I then installed the cockpit parts and the cabin section was complete!
Leave a Reply